Customers also bought these popular items  

Spare Parts - Bottom Feed

FREE SHIPPING on Orders over $199.00

1/3

6 MONTHS INTEREST-FREE WITH PAYPAL CREDIT™

 

2098 Cup Parts Kit - New SEPTEMBER 2019

This Cup Parts Kit includes the 2095 Assembly wearable parts that you should always have on hand if you own a Fuji Spray 1 Qt. (1000cc) Cup. Kit has 3 each of 2036 gaskets, 2028 diaphragms, 2024 pressure tube with check valves and 9055 metal strainer.

 

All the parts shown in the kit can be ordered separately.

 

Please note* If you own a Gravity Cup please order a Gravity Cup Parts Kits instead.

List: $38.60   Our Price $28.95

2097-10 Cup Gaskets (10) - New SEPTEMBER 2019

A 5-Pack of Cup Gaskets for the 2095 1Qt. (1000cc) Bottom-Feed Cup.

 

The diaphragm 2096 must be used with these gaskets. Available only in packs of 10. If you have an older Fuji spray gun and do not intend to switch to the diaphragm (but we recommend you do) then please order the thicker 2036 gaskets.

List: $37.00   Our Price $27.75

2096-3 Plastic Diaphragms - New SEPTEMBER 2019

3-Pack of Plastic Diaphragms for 2095 1Qt. (1000cc) Bottom-Feed Cup.

 

The air hole in the diaphragm should be positioned at the rear of the cup (towards the handle). That is, unless you intend spraying upwards for any length of time. For spraying upwards, position the hole in the diaphragm towards the front of the spraygun. The idea is to keep the hole out of the paint as much as possible. These diaphragms, in combination with the pressure tube/check valve, cure the problem of paint backing up the pressure tube.

List: $13.80   Our Price $10.40

2024-5 Pressure Tubes

Plastic Check Valves 5_Pack for 1 Qt. (1000cc) Bottom-Feed Cup.

 

For T-Series and XPC Spray Guns. Pressure tubes with check valve installed. Available only in packs of 5. These tubes fit all Bottom Feed Fuji spray guns. If clogged, the check valve cannot be taken apart, however, they can be soaked in thinner for up to 30 minutes to free any blockage. If you need pressure tubes for your Gravity spray gun please refer to 2024L-5.

List: $19.90   Our Price $17.50

9055-10 Nylon Paint Strainers - New SEPTEMBER

These inexpensive Metal Paint Strainers fit at the end of the 2095 metal fluid tube. The filters are durable and long-lasting. Can be soaked in thinner to clean. Sold in packs of 10.

 

List: $20.30    Our Price $17.90

Spare Parts - Gravity Feed

2030 400cc Gravity Cup Parts Kit

This kit includes the wearable parts that you should always have on hand for your 400cc Gravity Cup. Parts shown in the kit can be ordered separately.

 

Please note: If you are purchasing a Gravity Cup Parts Kit for your 600cc/1000cc gravity cup please refer to 2060.

 

List: $34.90    Our Price $30.90

9050-5 400cc Gravity Cup Gaskets 

List: $19.70    Our Price $16.70

These gaskets fit the Fuji 400cc Gravity Cup Lids ONLY. Please install these gently so that the gaskets sits in the rim of the lid firmly or flush without any kinks or twists.

 

Please note: If you are purchasing Gravity Cup Gaskets for your 600cc or 1000cc gravity cup lids please refer to 9720-5.

 

2024L-5 600cc Gravity Cup Pressure Tubes

This kit includes the wearable long pressure tube/check valve parts that you should always have on hand for your 600cc Nylon Gravity Cup

 

Please note: No Gasket is necessary with the new 9860 Nylon Gravity Cup.

 

List: $20.30    Our Price $17.90

9720-5 600cc & 1000cc Gravity Cup Gaskets

These gaskets fit the Fuji 600cc & 1000cc Gravity Cups METAL Lids ONLY. Please install these gently so that the gaskets sits in the rim of the lid firmly or flush without any kinks or twists. Not for PLASTIC Gravity Cups

 

Please note: If you are purchasing Gravity Cup Gaskets for your 400cc gravity cup lid please refer to 9050-5.

 

List: $19.95    Our Price $16.95

8081-3 3oz Gravity Cup Gaskets 

Chemical Resistant Gaskets (clear) for 9730 3ozs. Miniature Gravity Cup.

 

List: $13.50    Our Price $10.50

Spare Parts - Turbine

4009-2 Turbine Filters - Mini-Mite

These Turbine Filters fit all older Mini-Mite™ Models, Semi PRO and Hobby PRO turbines. Coarse filter goes on the right hand side (as seen when looking at the front of the case) fine filter on the left.

 

To remove, simply turn the turbine on its side and grab the filter from below. Pull out. To replace, push the filter in as tight as possible and then pull down gently to fit the filter enclosure. The filter should be flush with the bottom of the metal filter enclosure. Washable in Paint Thinner.

 

Please note: These filters will not fit the new PLATINUM Mini-Mite Turbines. Use 7224-2 instead.

List: $9.25    Our Price $7.25

7224-2 Turbine Filters - Mini-Mite PLATINUM

These Turbine Filters fit only the new Mini-Mite™ PLATINUM Models. 

 

To remove, simply turn the turbine on its side and grab the filter from below. Pull out. To replace, push the filter in as tight as possible and then pull down gently to fit the filter enclosure. The filter should be flush with the bottom of the metal filter enclosure. Washable in Paint Thinner.

 

List: $9.90    Our Price $7.80

5029 Q-Turbine Filter

This Turbine Filter fits all Q-turbines

 

To remove, simply turn the turbine on its side and grab the filter from below. Pull out. To replace, push the filter in as tight as possible and then pull down gently to fit the filter enclosure. The filter should be flush with the bottom of the metal filter enclosure. Washable in Paint Thinner.

List: $9.10    Our Price $7.10

3072 Wireless Remote

Use this Wireless Remote to allow you to control the on/off of your Turbine. There is no need to walk back and forth to your Turbine anymore. It works really well with your other power tools too. Please note* Fuji Spray does not manufacture this item. It is a 3rd Party Manufacturer.

 

This device will work from within a frequency range of 60 feet away. 

 

  • Extend the lifetime of your Turbine motor

  • Convenience of not having to walk back and forth

  • 120v only

  • No setup.  Just plug it in.

List: $34.35    Our Price $25.95